|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Outdoor Accents? connector screw reduces installation time by driving easily without pre-drilling. Designed for installation with the Outdoor Accents? connectors, such as the APA21 90 deg angle, APLH light joist hangers and APGT gazebo ties, the screw's black finish accents any outdoor living project. The sharp-point of the screw enables fast starts.
|
The Simpson Strong-Tie? Strong-Drive? SDS heavy-duty connector screw is a 0.25 in Dia high-strength structural wood screw ideal for various connector installations as well as wood-to-wood and engineered-wood applications. It installs with no pre-drilling and has been extensively tested in various applications. The SDS is improved with an easy-driving Type-17 point and a corrosion-resistant double-barrier coating. The SDS Strong-Drive? 1/4 in wood screw line has expanded to include stainless steel SDS screws in 1-1/2 to 3-1/2 in lengths, suitable for fastening Simpson Strong-Tie? stainless steel products. Offering the same easy-driving, split-reducing installation of the standard SDS screw, these screws are made from Type 316 stainless steel. The stainless steel SDS screws are appropriate for higher-exposure environments where maximum corrosion resistance is required.
|
Camo exterior fasteners are designed specifically for exterior projects. Each screw starts fast, holds strong, and is backed by a Camo warranty against rust and corrosion so you can confidently use them in all of your decking projects, substructures, landscaping, fences, pole barns and more.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Simpson Strong-Tie? Strong-Drive? SDS heavy-duty connector screw is a 0.25 in Dia high-strength structural wood screw ideal for various connector installations as well as wood-to-wood and engineered-wood applications. It installs with no pre-drilling and has been extensively tested in various applications. The SDS is improved with an easy-driving Type-17 point and a corrosion-resistant double-barrier coating. The SDS Strong-Drive? 1/4 in wood screw line has expanded to include stainless steel SDS screws in 1-1/2 to 3-1/2 in lengths, suitable for fastening Simpson Strong-Tie? stainless steel products. Offering the same easy-driving, split-reducing installation of the standard SDS screw, these screws are made from Type 316 stainless steel. The stainless steel SDS screws are appropriate for higher-exposure environments where maximum corrosion resistance is required.
|
The Simpson Strong-Tie? Strong-Drive? SDS heavy-duty connector screw is a 0.25 in Dia high-strength structural wood screw ideal for various connector installations as well as wood-to-wood and engineered-wood applications. It installs with no pre-drilling and has been extensively tested in various applications. The SDS is improved with an easy-driving Type-17 point and a corrosion-resistant double-barrier coating. The SDS Strong-Drive? 1/4 in wood screw line has expanded to include stainless steel SDS screws in 1-1/2 to 3-1/2 in lengths, suitable for fastening Simpson Strong-Tie? stainless steel products. Offering the same easy-driving, split-reducing installation of the standard SDS screw, these screws are made from Type 316 stainless steel. The stainless steel SDS screws are appropriate for higher-exposure environments where maximum corrosion resistance is required.
|
The Outdoor Accents? structural wood screw reduces installation time by driving easily without pre-drilling. When combined with the patented, load-rated Outdoor Accents? hex head washer, the solution delivers the decorative appearance of a bolt connection but with a much easier installation. The structural wood screw is now available in three sizes 2 in, 3-1/2 in and 5-1/2 in and can be used with either the Mission Collection? or Avant Collection?, as well as separately to add flair to any outdoor project. The 3-1/2 in and 5-1/2 in screws are ideal for structural applications. They feature a bold thread design that enables excellent holding to attach ledgers and other secure connections. The 2 in screw is ideal for use with 2X lumber and for adding style to any DIY project.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Camo exterior fasteners are designed specifically for exterior projects. Each screw starts fast, holds strong, and is backed by a Camo warranty against rust and corrosion so you can confidently use them in all of your decking projects, substructures, landscaping, fences, pole barns and more.
|
Interior wood screws provide fastening solutions that ensure a safer, stronger indoor living environment. The versatile wafer head screw is designed for general wood-to-wood fastening where its pull-through resistance is an advantage. This versatile screw features a sharp-point for easy installation and is ideal for everything from cabinetry to framing.
|
The Simpson Strong-Tie? Strong-Drive? SDS heavy-duty connector screw is a 0.25 in Dia high-strength structural wood screw ideal for various connector installations as well as wood-to-wood and engineered-wood applications. It installs with no pre-drilling and has been extensively tested in various applications. The SDS is improved with an easy-driving Type-17 point and a corrosion-resistant double-barrier coating. The SDS Strong-Drive? 1/4 in wood screw line has expanded to include stainless steel SDS screws in 1-1/2 to 3-1/2 in lengths, suitable for fastening Simpson Strong-Tie? stainless steel products. Offering the same easy-driving, split-reducing installation of the standard SDS screw, these screws are made from Type 316 stainless steel. The stainless steel SDS screws are appropriate for higher-exposure environments where maximum corrosion resistance is required.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
The Strong-Drive? SD connector screw is specifically designed to replace nails in certain Simpson Strong-Tie? connectors and is the only screw approved for that application. The load-rated SD screw has been tested and approved for use in many popular Simpson Strong-Tie? products. In certain applications screws are easier and more convenient to install than nails and the single-fastener load values achieved by the SD screw exceed those of typical 10d common or 16d common nails. In addition, the galvanized coating makes the SD screw ideal for interior and most exterior conditions.
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The SDWS Framing screw is designed and load-rated for replacing 16d, 10d and 8d nails in framing applications. The SDWS Framing screw is great to nails in holding power and pull-out resistance. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications. The screw has a SawTooth? point that makes for fast installations with reduced torque without predrilling and its specially designed head countersinks easily to provide a clean, flush finish. The T25 bit holds the 6-lobe recess tightly for more secure drive control.
|
The SDWS Framing screw is designed and load-rated for replacing 16d, 10d and 8d nails in framing applications. The SDWS Framing screw is great to nails in holding power and pull-out resistance. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications. The screw has a SawTooth? point that makes for fast installations with reduced torque without predrilling and its specially designed head countersinks easily to provide a clean, flush finish. The T25 bit holds the 6-lobe recess tightly for more secure drive control.
|
The SDWS Framing screw is designed and load-rated for replacing 16d, 10d and 8d nails in framing applications. The SDWS framing screw is excellent to nails in holding power and pull-out resistance. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications. The screw has a SawTooth? point that makes for fast installations with reduced torque without pre-drilling and its specially designed head countersinks easily to provide a clean, flush finish. The T25 bit holds the six-lobe recess tightly for more secure drive control.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strong-Drive? SD connector screw is specifically designed to replace nails in certain Simpson Strong-Tie? connectors and is the only screw approved for that application. The load-rated SD screw has been tested and approved for use in many popular Simpson Strong-Tie? products. In certain applications screws are easier and more convenient to install than nails and the single-fastener load values achieved by the SD screw exceed those of typical 10d common or 16d common nails. In addition, the galvanized coating makes the SD screw ideal for interior and most exterior conditions.
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
GRK's RSS??? screw is made of specially hardened steel to provide you with high tensile, torque and shear strength. The sharp threads and points bite instantly into the material (including hardwood), reducing the splitting effect due to smaller shanks. RSS??? screws that are 3-1/8 in and longer have CEE threads which enlarge the screw hole for the non-threaded portion of the fastener, allowing the wood to settle easily and increases the screw's drawing strength. The CEE thread also reduces the friction on the screw shank which can result in lowering the driving torque and the likelihood of splitting the wood. This is why the RSS??? screw is an efficient lag screw alternative. Our round head with built-in shield (washer type head) has no sharp edges like conventional lag screws. The added shoulder (nominal diameter) underneath the washer has the ability to center the RSS??? screw in pre-drilled hardware like hinges and connector plates.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
Camo exterior fasteners are designed specifically for exterior projects. Each screw starts fast, holds strong, and is backed by a Camo warranty against rust and corrosion so you can confidently use them in all of your decking projects, substructures, landscaping, fences, pole barns and more.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Simpson Strong-Tie? Strong-Drive? SDS heavy-duty connector screw is a 0.25 in Dia high-strength structural wood screw ideal for various connector installations as well as wood-to-wood and engineered-wood applications. It installs with no pre-drilling and has been extensively tested in various applications. The SDS is improved with an easy-driving Type-17 point and a corrosion-resistant double-barrier coating. The SDS Strong-Drive? 1/4 in wood screw line has expanded to include stainless steel SDS screws in 1-1/2 to 3-1/2 in lengths, suitable for fastening Simpson Strong-Tie? stainless steel products. Offering the same easy-driving, split-reducing installation of the standard SDS screw, these screws are made from Type 316 stainless steel. The stainless steel SDS screws are appropriate for higher-exposure environments where maximum corrosion resistance is required.
|
The Strong-Drive? SD connector screw is specifically designed to replace nails in certain Simpson Strong-Tie? connectors and is the only screw approved for that application. The load-rated SD screw has been tested and approved for use in many popular Simpson Strong-Tie? products. In certain applications screws are easier and more convenient to install than nails and the single-fastener load values achieved by the SD screw exceed those of typical 10d common or 16d common nails. In addition, the galvanized coating makes the SD screw ideal for interior and most exterior conditions.
|
The Simpson Strong-Tie? Strong-Drive? SDS heavy-duty connector screw is a 0.25 in Dia high-strength structural wood screw ideal for various connector installations as well as wood-to-wood and engineered-wood applications. It installs with no pre-drilling and has been extensively tested in various applications. The SDS is improved with an easy-driving Type-17 point and a corrosion-resistant double-barrier coating. The SDS Strong-Drive? 1/4 in wood screw line has expanded to include stainless steel SDS screws in 1-1/2 to 3-1/2 in lengths, suitable for fastening Simpson Strong-Tie? stainless steel products. Offering the same easy-driving, split-reducing installation of the standard SDS screw, these screws are made from Type 316 stainless steel. The stainless steel SDS screws are appropriate for higher-exposure environments where maximum corrosion resistance is required.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Easy to install lag alternative. Zero stripping recessed star drive. Cee thread for a clean finished look. W-Cut for low torque, smoother drive. ZIP-TIP for no pre-drilling, faster penetration. Washer head provides immense holding power. Cutting pockets provide a clean hole, reduces splitting, and bore with precision. ESR-3201 Approved for structural application. Climatek Coated: AC257 code approved for use in treated lumber. For interior/exterior use in: carrying beams, ledger boards, stair rails, deck posts, playground equipment and other professional applications.
|
The Strong-Drive? SD connector screw is specifically designed to replace nails in certain Simpson Strong-Tie? connectors and is the only screw approved for that application. The load-rated SD screw has been tested and approved for use in many popular Simpson Strong-Tie? products. In certain applications screws are easier and more convenient to install than nails and the single-fastener load values achieved by the SD screw exceed those of typical 10d common or 16d common nails. In addition, the galvanized coating makes the SD screw ideal for interior and most exterior conditions.
|
Camo exterior fasteners are designed specifically for exterior projects. Each screw starts fast, holds strong, and is backed by a Camo warranty against rust and corrosion so you can confidently use them in all of your decking projects, substructures, landscaping, fences, pole barns and more.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
The Strong-Drive? SDWS timber screw is designed to provide an easy to install, high-strength alternative to through-bolting and traditional lag screws. This screw is ideal for the contractor and do-it-yourselfer alike. It is code listed in IAPMO UES ER-192 and meets 2018 and 2021 IRC? and IBC? code requirements for most common wood framing applications.
|
Easy to install lag alternative. Zero stripping recessed star drive. Cee thread for a clean finished look. W-Cut for low torque, smoother drive. ZIP-TIP for no pre-drilling, faster penetration. Washer head provides immense holding power. Cutting pockets provide a clean hole, reduces splitting, and bore with precision. ESR-3201 Approved for structural application. Climatek Coated: AC257 code approved for use in treated lumber. For interior/exterior use in: carrying beams, ledger boards, stair rails, deck posts, playground equipment and other professional applications.
|
|
|
