|
|
|
|
|
|
|
|
|
|
|
|
|
|
Set of 2 for standard 2-1/2 in resilient motor mounting rings.
|
Standard compression sleeve for 1/4 in OD copper tube.
|
Prevents sagging and movement. Replacement for Champion Coolers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Includes slip in, non-threaded overflow pipe, washer, poly drain with 3/4 in male garden hose threads.
|
Prevents sagging and movement. Replacement for Artic Circle, Arvin and McGraw.
|
Fits all offset and concentric pumps.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Standard compression sleeve and nut for 1/4 in O.D copper tube. Two nuts and two sleeves.
|
1/2 in MPT overflow pipe with flat sided hex head for easy install and removal. Washer included. Nylon drain with 1/2 in FTP ID and 3/4 in male garden hose threads OD.
|
1/4 in CC x 1/8 in MPT. Use with copper or poly tube on side tapped sill cock or pipe adapter. Includes poly tube adapter.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Adapts poly tube to brass fittings without using 1/4 in CC sleeve.
|
Provides a one step treatment to inhibit build-up of scale, rust and offensive odor. Conditions cooler pad to reduce air temperature. Contains mild acid and wetting agents, not for potable water.
|
Kit fits 3-way side, 4-way down, 6-way side and 8-way down by using an 8 way down distributor with up to 5 inserts plugs and MEK. Includes distributor head, water distributor adapter, MEK solvent and instructions.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Standard for residential and commercial pumps with 4500 to 11,000 cfm ratings. Use to run water from pump to distributor.
|
Formed basket, fits all pumps. 8 in L x 6 in W x 3-1/2 in H.
|
20-1/8 in end to bend length. Fits all residential coolers.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Replacement latch for Arctic Circle, Arvin, McGraw and Wright coolers, may be retrofitted to all coolers. Sun resistant.
|
1/4 in CC x 1/8 MPT straight water shut-off valve. Includes poly tube adapter.
|
1/4 in CC x 1/8 MPT Angle water shut off valve. Includes poly tube adapter, fits sill cocks and pipe adapter.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dial Compression Union, Specifications: 1/4 in x 1/4 in Compression Connection Type, Brass, Dimensions: 1/4 in Dia, Suitable for: Evaporative Cooler Purge Systems, Includes: (1) Poly Tube Adapter
|
Lubricate shaft bearings at the start of every season and every 60 days during season.
|
Controls scale build-up and corrosion in coolers, special formula holds minerals in suspension by raising the solubility level of the water. Reduces mineral build-up on pads must be used with a bleed off kit or PowerClean? purge pump to flush suspended minerals.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
1/4 in CC Tee, for connecting two coolers to one water source. Includes poly tube adapters.
|
A time release formula that controls unpleasant odors from algae and bacteria in evaporative coolers and neutralizes odor in cooler water to freshen the air. Not for potable (drinkable) water.
|
Premium, heavy-bodied, "one coat" coating. Apply with a brush. Designed to coat and seal evaporative cooler bottom pans, protect against rust and corrosion all season, help deaden sound. Resistant to moisture, non-asbestos and fast drying.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Brass inlet, arm and stem. Polypropylene body and float. Noiseless and non-corrosive.
|
1/4 in CC straight in-line water shut-off valve. Includes poly tube adapters for 1/4 in poly tube.
|
Resistant to UV degradation, use to run water to coolers, not for potable water. Do not use indoors or in attic.
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
|
Dial Pillow Block Bearing, Dimensions: 3/4 in Dia, Suitable for: Evaporative Cooler Purge Systems
|
Includes distributor tubes, distributor head, water distributor adapter, MEK solvent and instructions.
|
Dial Pillow Block Bearing, Dimensions: 5/8 in Dia, Suitable for: Evaporative Cooler Purge Systems
|
|
|
